Precautions and maintenance of low-speed refrigerated centrifuge

In addition to the general centrifuge structural functions, low-speed refrigerated centrifuges also have refrigeration, vibration reduction, instrument control and other systems. Clinically, it is mainly used to separate, precipitate and concentrate the test solution to extract the components of different specific gravity in the sample. therefore. Correct operation and reasonable maintenance are the key to ensure the normal operation of the instrument and extend the service life of the instrument:

Notes on instrument operation:

1. To prevent contamination of the instrument by radioisotopes, first carefully observe the sample tube for cracks or trachoma to avoid liquid leakage during centrifugation; secondly, the plastic tube that puts the centrifuge cup should be light. Prevent liquid splashing: If the liquid enters the centrifuge cup and causes contamination in the centrifuge cavity, the centrifuge cup should be taken out immediately, rinsed with tap water and dried, and the centrifuge cavity should be thoroughly cleaned.

2. To maintain the stability of the internal and external use environment of the centrifuge, the DDL-5 centrifuge should be placed horizontally, more than 10cm away from the wall, and maintain a good ventilation environment, protected from direct exposure to heat sources and sun rays. Cooling effect. When the outside humidity is high, the water in the centrifuge cavity evaporates slowly, and it should be removed in time to prevent the instrument from rusting. When centrifuging the sample tube just removed from the water temperature box, you should always observe whether there is water in the centrifuge cup and pour it in time to keep the centrifuge cup dry and the balance during centrifugation.

3. To prevent the aging of the sealing ring, the upper part of the centrifuge cavity is equipped with a rubber sealing ring at the contact with the door. As the use time increases, it should be regularly observed for deformation to prevent external heat from infiltrating people, which will affect the test result due to poor cooling effect.

4. Set the temperature correctly. When setting the temperature, the upper limit setting value must be too high than the lower limit setting temperature value, otherwise the lower limit setting temperature will be 2 ° C lower than the upper limit setting temperature.

5. Set the speed correctly. When setting the speed, it must be set after the timer is turned on. First convert the required speed into frequency (1H = 60rpm), then press â–³ or v key to change the required frequency, after a few seconds the frequency will be automatically converted

Rotation speed: when the instrument is running to change the rotation speed, the SHIUF key cannot be used, otherwise it will cause the program to be disordered. The speed setting should never exceed the maximum speed to ensure the safe rotation of the instrument.

6. When there is 0 or other digital machine does not run during use, it should be turned off and off for 10s, and then restarted. After the set speed is displayed, press the reverse key.

maintain:

1. Regular maintenance. As with the maintenance of other medical instruments, in addition to the routine inspection and maintenance of electrical circuits, electronic circuits, and mechanical rotating parts, pay attention to the damage and aging of various indicators.

2. Keep the centrifugal cup symmetrically balanced. Although the centrifuge has a secondary shock absorption device, such as the unbalanced sample tube placed in the centrifuge chamber, it will cause the centrifuge to shake and shift. After shutdown and reset, you should carefully check whether the instrument is normal.

3. The door bolts of the centrifuge cover should be checked frequently to maintain flexibility to prevent forced opening or closing. When bad contact occurs, it should be repaired and replaced in time. For common faults, we should pay more attention to observation and eliminate in time.

4. Do a good job of registering the working state of the centrifuge and each working time, recording the original fault of the instrument and troubleshooting methods, and asking in time to ensure that the instrument is working in the best state.

Resistance Loop Workout Our exercise bands are made from high quality environmentally friendly latex material, they are free of non-natural materials and more smooth and comfortable, stronger, stretch further and last longer.This exercises Workout Bands meet your all kinds of exercise needs, help you meet your long-term fitness goals, and reduce depression and stress, also can be good physical therapy bands for rehabilitation.

Resistance Loop Workouts

Resistance Loop Workout,Work Out Bands,Exercise Band Workouts,Workout Bands

Shandong Shangkun Sports Health Technology Co.,Ltd. , http://www.shangkunsports.com