Shanghai Haozhuang Instrument Co., Ltd. developed the LNB brand anaerobic incubator, which is energy-saving and environmentally friendly, leading the country. The anaerobic incubator is a special device for bacteria cultivation and operation under anaerobic environment. It can provide strict anaerobic state constant temperature cultivation conditions and has a systematic and scientific work area. Operating and cultivating in this device can cultivate the anaerobic organisms that are the most difficult to grow, and can avoid the risk of anaerobic organisms being exposed to oxygen and dying when operating in the atmosphere. Therefore, this device is an ideal tool for anaerobic biological detection and scientific research. The device is also a good instrument with multiple uses, such as changing the operation mode to provide good growth conditions for the growth and reproduction of microaerobic bacteria.
Instructions for use (1), the formation of an anaerobic environment in the operating room 1) Place the necessary accessories and appliances according to the requirements of the use, and put two five poisonous plastic bags into the operating room. 2) Adjust the input pressure of the mixed gas cylinder and nitrogen cylinder, adjust the pressure reducing valve so that the input pressure is 0.1Mpa 3) After opening the device, after the power switch is pressed, press the main power button on the control card to energize the device. 4) Put 1000g of palladium particles (sealed) and 500g of desiccant in the operation room, and put the Meilan indicator strip. 5) Close the indoor and outdoor doors of the sampling, and vacuum check. (Press the vacuum pump button on the control panel, press on, and then off again) 6) The first replacement in the operating room (nitrogen replacement): (1) First insert the rubber tube into the air inlet of the operating room, and the other into the plastic bag . (2) Connect the nitrogen gas inlet, open the nitrogen control valve in the operation room, and make the two plastic bags full of nitrogen, then close the solenoid valve, and then tighten the bag mouth. (3) Put the latex gloves on the flange ring of the observation board and tighten it. (4) Gradually put the nitrogen in the plastic bag in the operation room until it is completely eliminated. 7) Repeat the second flush of the operation room (nitrogen replacement). In the nitrogen process, the sampling chamber is first evacuated, and pay attention to close the exhaust by pressing the exhaust valve at any time. 8) The third replacement of the operation room (mixed gas replacement) (mixed gas ratio is H2 1/85% H2 1/10% H2 1/10% CO2 / 15%) (1) Change the gas path and open the operation room mixture When the valve is inhaled, the sampling chamber is first evacuated when flushing, and pay attention to close the exhaust by pressing the exhaust valve at any time. (2) After the mixed gas is filled in the plastic bag, close the solenoid valve and open the mixed gas restrictor valve, so that the mixed gas passes through the flow stabilizer, flowmeter, and adjust the flowmeter, and the flow rate is about 10 ml per minute. (3) The mixed gas in the plastic bag is gradually discharged into the operating room. (4) After three times of ventilation, the oxygen content of the gas in the operation room is already in the extreme state 9) Open the palladium particle deaerator in the operation room, connect the power of the deaeration catalyst for catalytic deaeration, and react in the anaerobic indicator Put a little clean water on the area. After 1-2 hours, observe the discoloration. The dark blue color changes to light blue in the reaction area to achieve an anaerobic environment in the operating room. Note: 1 The indicator strip can be used repeatedly, 2 Do not touch the blue reaction area 3 Pack the spring in the sealed tube, prevent it from being in a dry place. 10Ultraviolet sterilization lamp, sterilization treatment in the room, the sterilization time is customized.Precautions for installation 1. The whole machine should be placed in a place with small temperature difference and convenient operation. Avoid direct sunlight and heating equipment, keep it stable; 2. Place the mixed gas bottle and nitrogen bottle stably, and install the decompression Valves (including pressure gauges) should be placed in the proper position; 3. Connect the gas circuit and check the gas circuit. In order to prevent air leakage, if necessary, they can be bonded with sealant at each connection.
Shanghai Haozhuang has a recognized team of experts in the industry and first-class scientific and technological talents, with a deep understanding and mastery of scientific instrument technology, serving customers!
Sanitary Napkins For Night Use
Lady Sanitary Pad,Anion Sanitary Napkins,Women Sanitary Napkin,Eco Friendly Sanitary Napkins
Shandong Tianzige International Trade Co., Ltd , https://www.chinesedipers.com