What to do if the basin sink plugs up? How to install the basin sink?
People's daily cleanliness can not be separated from the basin, but they want to discharge the waste water in the basin. It is inseparable from the basin water filter. The basin water device is a drainage device installed in the basin sewer, etc. It exists to ensure the basin's Normal use. Next, Xiao Bian will explain to you how to install the basin of water into the water and other related knowledge, learn it together.
Basin classification of water pipes
1, press-type water device
Although the appearance of the push-type discharge device looks good, the press-type discharge water is more likely to adhere to some dirt. The entire discharge device needs to be screwed off to perform thorough cleaning, and the operation will be slightly complicated, and it is not very convenient to use. If the water filter is unscrewed, the safety may be loosened and not firm.
2, flip type water device
The flap launcher can be rotated in any direction, resulting in water leakage in the basin. After a long time, the flap type popper will have a reduced sealability, which will make it impossible for the basin to contain water. Or the situation that it does not turn over; flip-type water absorber is simple in structure, easy to clean, and easy to replace.
3, the drain water device
The structure of the drain trap is also relatively simple. It is almost the same as the kitchen sink. The assembly and disassembly procedures of the drain trap are slightly more complicated than the installation of the press-type pop-up device and the flap-type pop-up device. The sink drain basin cannot hold water unless it is sealed.
Basin water dispenser installation procedure
1, first come up with the purchase of the water dispenser, the lower part of the basin into the water fixture and the flange open, and then the basin flange of the water pipe tightly buckled under the basin, we must put the flange tight, After the tightening, you can put the basin on the top of the table, and one end of the basin's water pipe is aligned with the hole on the top of the basin.
2, in the appropriate position of the basin under the water pipe wrapped in some anti-seepage of the tape, and then the other end of the basin water pipe at the sewer, which is the sewage drainage pipe at the hole, to adjust the basin water pipe accessories or Take out the parts and use a wrench to tighten the interface between the lower water dispenser and the sewer pipe. After the installation is completed, check whether the two ends of the basin water pipe are evenly adjusted and tightened.
3. Check if there are no parts or flats in the installation process. After checking that there are no errors, the water inside the basin starts to be tested and the water is leaked from the side. If there is no water leakage or water seepage, it means that the plumbing under the basin is installed; otherwise, you need to recheck or reinstall it.
What to do if the basin water filter is blocked?
If drainage runs slowly, it may be a problem of hair clogging. The following method is not charming, but it is often effective. That is, using a hanger, straighten it so that you can slide the curved end drain hole. Move it to the hair-dragging position and slowly pull it out of the sewer and pull it out of the hair. Clear the problem of accumulation of hair blocked, you can also pour some detergent or similar products into the sewer and wait 30 minutes before running hot water flushing drainage.
If you do not want to use harsh chemicals, you can also pour soda into the sewer, followed by half a glass of white vinegar. Use rags to cover the drain and quickly drain into the drain hole. Baking soda and vinegar will react, so it's important to keep the drain hole covered so the content doesn't run away. Slowly remove the oil drain plug after 30 minutes and pour 1 gallon of boiling hot water into the drain to solve the plugging problem.
How to remove the basin water dispenser
If you want to remove the basin water dispenser, you must first look at the glass glue. If you don't have it, simply release it from below. If you have glass glue, use a blade or something else to get him. Under the basin, there is usually a rotating fixture that can only be seen when you turn to the bottom, or you can touch it and you can usually find it.
How to do when the basin water leaks?
First install the basin with proper amount of water, and then open the drain valve. First check whether the pipe is leaking or the water valve is leaking. If the pipe leaks, change it. The water valve leaks first. Check if the raw tape is not wrapped up. If it is still leaking, seal it. Firmly replace the water valve, do not twist it when installing, use special clamps, otherwise it is easy to twist the threads in the water valve.
Basin basin water device cleaning method
1. When the basin water switch is in the bounced drain state. Hold the bouncing water switch by hand and rotate it counterclockwise. The water switch cover is unscrewed.
2, after being screwed off, rinse directly with water, you can also use a small brush to scrub.
3, the sewer will also gather a lot of dirt like hair, and then use a small spoon to trap the drain of hair and the like. Rinse again with water.
4. Make sure the rinse is clean. Then turn the cover of the drain switch clockwise.
<\p><\div>
Dog Cotton Rope Toys,Foam Rope Bone Dog Toy ,Cotton Rope Tug Of War Toy ,Pet Dog Chew Toy
Shaoxing City Heou Leisure Goods Co., Ltd. , https://www.heoupettoy.cn